diff --git a/arduino/ws2812_controller/ws2812_controller.ino b/arduino/ws2812_controller/ws2812_controller.ino
index 0316838..19d7bf6 100644
--- a/arduino/ws2812_controller/ws2812_controller.ino
+++ b/arduino/ws2812_controller/ws2812_controller.ino
@@ -1,79 +1,79 @@
-#include <Arduino.h>
-#include <ESP8266WiFi.h>
-//#include <WebSocketsServer.h>
-//#include <Hash.h>
-#include <WiFiUdp.h>
-#include <NeoPixelBus.h>
-
-// Set to the number of LEDs in your LED strip
-#define NUM_LEDS 242
-// Maximum number of packets to hold in the buffer. Don't change this.
-#define BUFFER_LEN 726
-// Toggles FPS output (1 = print FPS over serial, 0 = disable output)
-#define PRINT_FPS 1
-
-//NeoPixelBus settings
-const uint8_t PixelPin = 3;  // make sure to set this to the correct pin, ignored for Esp8266(set to 3 by default for DMA)
-
-// Wifi and socket settings
-const char* ssid     = "ASUS_VIVOBOOK";
-const char* password = "T!PT)Psecret";
-unsigned int localPort = 7778;
-byte packetBuffer[BUFFER_LEN];
-RgbColor ledDataBuffer[NUM_LEDS];
-
-// LED strip
-NeoPixelBus<NeoGrbFeature, Neo800KbpsMethod> ledstrip(NUM_LEDS, PixelPin);
-
-WiFiUDP port;
-
-// Network information
-// IP must match the IP in config.py
-IPAddress ip(192, 168, 137, 200);
-// Set gateway to your router's gateway
-IPAddress gateway(192, 168, 137, 1);
-IPAddress subnet(255, 255, 255, 0);
-
-void setup() {
-    Serial.begin(115200);
-    //WiFi.config(ip, gateway, subnet);
-    WiFi.mode(WIFI_STA);
-    WiFi.begin(ssid, password);
-    Serial.println("");
-    // Connect to wifi and print the IP address over serial
-    while (WiFi.status() != WL_CONNECTED) {
-        delay(500);
-        Serial.print(".");
-    }
-    Serial.println("");
-    Serial.print("Connected to ");
-    Serial.println(ssid);
-    Serial.print("IP address: ");
-    Serial.println(WiFi.localIP());
-    port.begin(localPort);
-    ledstrip.Begin();//Begin output
-    ledstrip.Show();//Clear the strip for use
-}
-
-uint8_t N = 0;
-#if PRINT_FPS
-    uint16_t fpsCounter = 0;
-    uint32_t secondTimer = 0;
-#endif
-
-void loop() {
-    // Read data over socket
-    int packetSize = port.parsePacket();
-    // If packets have been received, interpret the command
-    if (packetSize) {
-        int len = port.read(packetBuffer, BUFFER_LEN);
-        for(int i = 0; i < len; i+=4) {
-            packetBuffer[len] = 0;
-            N = packetBuffer[i];
-            RgbColor pixel((uint8_t)packetBuffer[i+1], (uint8_t)packetBuffer[i+2], (uint8_t)packetBuffer[i+3]);
-            ledstrip.SetPixelColor(N, pixel);
-        }
-        ledstrip.Show();
-        Serial.print("/");
-    }
+#include <Arduino.h>
+#include <ESP8266WiFi.h>
+//#include <WebSocketsServer.h>
+//#include <Hash.h>
+#include <WiFiUdp.h>
+#include <NeoPixelBus.h>
+
+// Set to the number of LEDs in your LED strip
+#define NUM_LEDS 242
+// Maximum number of packets to hold in the buffer. Don't change this.
+#define BUFFER_LEN 726
+// Toggles FPS output (1 = print FPS over serial, 0 = disable output)
+#define PRINT_FPS 1
+
+//NeoPixelBus settings
+const uint8_t PixelPin = 3;  // make sure to set this to the correct pin, ignored for Esp8266(set to 3 by default for DMA)
+
+// Wifi and socket settings
+const char* ssid     = "YOUR_WIFI_SSID";
+const char* password = "YOUR_WIFI_PASSWORD";
+unsigned int localPort = 7778;
+byte packetBuffer[BUFFER_LEN];
+RgbColor ledDataBuffer[NUM_LEDS];
+
+// LED strip
+NeoPixelBus<NeoGrbFeature, Neo800KbpsMethod> ledstrip(NUM_LEDS, PixelPin);
+
+WiFiUDP port;
+
+// Network information
+// IP must match the IP in config.py
+IPAddress ip(192, 168, 137, 200);
+// Set gateway to your router's gateway
+IPAddress gateway(192, 168, 137, 1);
+IPAddress subnet(255, 255, 255, 0);
+
+void setup() {
+    Serial.begin(115200);
+    //WiFi.config(ip, gateway, subnet);
+    WiFi.mode(WIFI_STA);
+    WiFi.begin(ssid, password);
+    Serial.println("");
+    // Connect to wifi and print the IP address over serial
+    while (WiFi.status() != WL_CONNECTED) {
+        delay(500);
+        Serial.print(".");
+    }
+    Serial.println("");
+    Serial.print("Connected to ");
+    Serial.println(ssid);
+    Serial.print("IP address: ");
+    Serial.println(WiFi.localIP());
+    port.begin(localPort);
+    ledstrip.Begin();//Begin output
+    ledstrip.Show();//Clear the strip for use
+}
+
+uint8_t N = 0;
+#if PRINT_FPS
+    uint16_t fpsCounter = 0;
+    uint32_t secondTimer = 0;
+#endif
+
+void loop() {
+    // Read data over socket
+    int packetSize = port.parsePacket();
+    // If packets have been received, interpret the command
+    if (packetSize) {
+        int len = port.read(packetBuffer, BUFFER_LEN);
+        for(int i = 0; i < len; i+=4) {
+            packetBuffer[len] = 0;
+            N = packetBuffer[i];
+            RgbColor pixel((uint8_t)packetBuffer[i+1], (uint8_t)packetBuffer[i+2], (uint8_t)packetBuffer[i+3]);
+            ledstrip.SetPixelColor(N, pixel);
+        }
+        ledstrip.Show();
+        Serial.print("/");
+    }
 }