Delete config.py

python/config.py

@@ -1,104 +0,0 @@
-"""Settings for audio reactive LED strip"""
-from __future__ import print_function
-from __future__ import division
-import os
-
-DEVICE = 'esp8266'
-"""Device used to control LED strip. Must be 'pi',  'esp8266' or 'blinkstick'
-
-'esp8266' means that you are using an ESP8266 module to control the LED strip
-and commands will be sent to the ESP8266 over WiFi.
-
-'pi' means that you are using a Raspberry Pi as a standalone unit to process
-audio input and control the LED strip directly.
-
-'blinkstick' means that a BlinkstickPro is connected to this PC which will be used
-to control the leds connected to it.
-"""
-
-if DEVICE == 'esp8266':
-    UDP_IP = '192.168.0.150'
-    """IP address of the ESP8266. Must match IP in ws2812_controller.ino"""
-    UDP_PORT = 7777
-    """Port number used for socket communication between Python and ESP8266"""
-    SOFTWARE_GAMMA_CORRECTION = False
-    """Set to False because the firmware handles gamma correction + dither"""
-
-if DEVICE == 'pi':
-    LED_PIN = 18
-    """GPIO pin connected to the LED strip pixels (must support PWM)"""
-    LED_FREQ_HZ = 800000
-    """LED signal frequency in Hz (usually 800kHz)"""
-    LED_DMA = 5
-    """DMA channel used for generating PWM signal (try 5)"""
-    BRIGHTNESS = 255
-    """Brightness of LED strip between 0 and 255"""
-    LED_INVERT = True
-    """Set True if using an inverting logic level converter"""
-    SOFTWARE_GAMMA_CORRECTION = True
-    """Set to True because Raspberry Pi doesn't use hardware dithering"""
-
-if DEVICE == 'blinkstick':
-    SOFTWARE_GAMMA_CORRECTION = True
-    """Set to True because blinkstick doesn't use hardware dithering"""
-
-USE_GUI = True
-"""Whether or not to display a PyQtGraph GUI plot of visualization"""
-
-DISPLAY_FPS = True
-"""Whether to display the FPS when running (can reduce performance)"""
-
-N_PIXELS = 60
-"""Number of pixels in the LED strip (must match ESP8266 firmware)"""
-
-GAMMA_TABLE_PATH = os.path.join(os.path.dirname(__file__), 'gamma_table.npy')
-"""Location of the gamma correction table"""
-
-MIC_RATE = 44100
-"""Sampling frequency of the microphone in Hz"""
-
-FPS = 60
-"""Desired refresh rate of the visualization (frames per second)
-
-FPS indicates the desired refresh rate, or frames-per-second, of the audio
-visualization. The actual refresh rate may be lower if the computer cannot keep
-up with desired FPS value.
-
-Higher framerates improve "responsiveness" and reduce the latency of the
-visualization but are more computationally expensive.
-
-Low framerates are less computationally expensive, but the visualization may
-appear "sluggish" or out of sync with the audio being played if it is too low.
-
-The FPS should not exceed the maximum refresh rate of the LED strip, which
-depends on how long the LED strip is.
-"""
-_max_led_FPS = int(((N_PIXELS * 30e-6) + 50e-6)**-1.0)
-assert FPS <= _max_led_FPS, 'FPS must be <= {}'.format(_max_led_FPS)
-
-MIN_FREQUENCY = 200
-"""Frequencies below this value will be removed during audio processing"""
-
-MAX_FREQUENCY = 12000
-"""Frequencies above this value will be removed during audio processing"""
-
-N_FFT_BINS = 24
-"""Number of frequency bins to use when transforming audio to frequency domain
-
-Fast Fourier transforms are used to transform time-domain audio data to the
-frequency domain. The frequencies present in the audio signal are assigned
-to their respective frequency bins. This value indicates the number of
-frequency bins to use.
-
-A small number of bins reduces the frequency resolution of the visualization
-but improves amplitude resolution. The opposite is true when using a large
-number of bins. More bins is not always better!
-
-There is no point using more bins than there are pixels on the LED strip.
-"""
-
-N_ROLLING_HISTORY = 2
-"""Number of past audio frames to include in the rolling window"""
-
-MIN_VOLUME_THRESHOLD = 1e-7
-"""No music visualization displayed if recorded audio volume below threshold"""